Purveyors of Electronic, Musical and Vintage goods from then, now and in between. 
Since 1982.

PA EQUIPMENT / STUDIO / PRO AUDIO / STAGE / SOUND REINFORCEMENT GEAR
USED AND NEW
 

PA Equipment / Studio gear & Professional Sound systems / speakers / amps for sale. Brands such as Mackie, Yamaha Peavey, DOD, Digitech, Alesis, BEHRINGER MODULIZER PRO DSP1224P and BEHRINGER VIRTUALIZER PRO DSP1024P , EV, Tascam Power amps / amplifiers, effects units & outboard gear, 12 & 16-channel snakes, Reverbs & 1/3 octave EQ / Equalizers for sale.
 

Hey Oak Tree. "Why all this OLD PA GEAR? Why don't I just get one of those new, shiny and cheaper models from one of the new, big-box whorehouses" (no slight meant on that 'oldest of professions')...?

Here's why;

I sold this type of 'pro-audio' equipment for years and watched the evolution from quality gear, built in the US and Japan to the current offerings at most stores and online, which is mostly cheap, 'disposable' 'trash-gear', built to last only a few years or even months coming out of China. Any of us 'experienced' audio guys can also appreciate the more precision, sturdy "feel" of the older, better built gear.

Firstly, check those new mixers-vs-the older one's. Older mixing boards are typically built with 'full size' potentiometers, secured to the top plate with 'shaft nuts'. Newer mixing boards (and frankly about anything with 'rotary' control potentiometers such as effects units, signal processors, keyboards, multi-tracks, power amps, stereo gear, etc) utilize pots that are only soldered to the circuit board, with no attachment to the top panel. That means that every time you manipulate the control with any pressure, you are flexing the solder joints that attach the control to the board. Before long you start having intermittent controls and channels. The other issue following along with that is that the 'PC Mounted' pots are usually not sealed very well and can allow a lot of dust / debris into them. NOW couple that with a 'gap' around their shaft going up thru the hole in the top panel, with no shaft nut to help 'seal' out the dirt / dust and the controls will become dirty MUCH, MUCH quicker on modern gear than on the old stuff.  Go ahead. Go over to your mixer that's made after about the late 1990's and was less than $1000 and 'wiggle' the knob. I bet it has quite a lot of lateral movement in it. Still in doubt. Pull one of the 'rotary' knobs off and see if there's a 'shaft nut' on it. If not, and there probably isn't, then there's nothing holding that control except for it's solder joints. Look at any vintage gear and it ALL has shaft nuts. Engineers wouldn't think of mounting a 'user accessible' control without a shaft nut back then. The consumer wants their gear cheap, and one of the way's manufactures save a considerable amount of money is by reducing the cost of the 'user controls'.

Secondly, check the Input / Output jacks / connectors. Older / Vintage mixing boards / consoles typically are using connectors (that are often made of 'metal', especially concerning the XLRs) that are attached to the rear metal panel with fasteners (screws / bolts / rivets etc). Modern mixers will almost always have the connectors attached in groups of 2, 4 or 6 with maybe 2 screws for the whole lot. Again, that means that every time you connect a cable, or 'pull laterally' on a cable or disconnect a cable, you are placing a strain on the solder joints, again leading to intermittent channels / connections / signals. Look at any vintage gear and it will have shaft nuts on the 1/4" jacks and at least 2 'diagonally located' fasteners on the XLR jacks. Engineers wouldn't think of mounting I/O jacks without fasteners back then.

Thirdly, most mid to upper end mixing boards from 'yesteryear' were constructed with the channels on 'modular' circuit boards (meaning that each channel was on it's own, vertically oriented, circuit board. Some of the 'lesser' quality models / brands would have channels grouped in 2-4 channels on a 'horizontally' positioned board). That meant that they were built for 'serviceability' down the road. That is MUCH more expensive than how they have been built from the mid-late 1990's to today. Modern mixing boards (at least your 'main stream / music store / bar band' variety under $3k) will most likely have ALL the channels located on ONE, horizontally positioned circuit board. That means that if you were to attempt to service one channel, you would have to remove ALL the knobs, and the ENTIRE circuit board to get to any of the components. but wait. WHAT COMPONENTS?...

Forth, there doesn't appear to be any components. At least not any that most folks with a soldering iron and a bit of electronics knowledge and common sense will recognize. Oh, they're still there. All the resistors, capacitors, diodes, transistors, etc. They're those little, tiny blocks that look like 'Sen Sen' breath fresheners (now I'm showing my age). Those little 'blocks' are called 'SMD's' (Surface Mount Devices). What, you can't see them. Go grab a magnifying glass and a good light, and while you're at it grab a soldering iron MUCH smaller than the one you have in your hand. Bottom line, "you ain't likely gonna be doin any work on that board". It's WAY, WAY cheaper for boards to be made like that. Hey, if they weren't using those 'SMD's' with all the features we consumers seem to want packed into our mixers now (multiple EQ's, 2-6 on board effects units / signal processors, 'Feedback killers', etc), the mixer would be the size of a 'Tuff Shed' and weigh about as much too.

More to come as time allows...

 

   

WORLDS BEST RACK SCREWS
WE MEAN IT!!!
Yeah I know it's just a rack screw, but if like me you've put in many hundreds or thousands of rack screws you know that a good percentage of them will cross-thread as soon as you start them. These will reduce the number of cross threaded starts you will have by many fold. They can even be successfully used to "fix" already cross-threaded holes. The main reason these are different is that their shaft is tapered smaller than the threads so it starts more accurately resulting in much fewer cross-threads. Due to the tapering it is also easier to start one of these screws when you have the screw gun or driver in one hand with the screw already stuck to the end,  and the piece of gear in the other doing a "balancing act" while trying to get the threads started. You can also have less fear starting these with a power driver. No more "gingerly" starting all you screws with a manual driver then switching to your power driver. These also feature an oversized head with matching nylon washer, great for worn, enlarged, or oversized holes in gear. I bet you never thought anyone could talk this long about something a simple as a rack screw, but these things really are the best I've ever encountered. Each is finished in a durable semi-gloss black coating and comes with size matched nylon bushing. They are designed for standard US threaded racks and will even fit SKB type clips. Sold in a bakers dozen (13).
$14.99 / 1 bag 
or
$12.99 / bag 2 or more

for quantities of more than 10 bags call for pricing.
 
Enough for *6 pieces of gear in a stationary situation or 3 pieces in a mobile road or flight case.
(Larger quantities available upon request)

* While it is permissible to use only 2 screws to mount most rack-mount items, the screws must be through the lower most holes, not the top ones or  used diagonally. If you use the lower ones, gravity will take care of the top. If there is any chance the rack will be tipped, rolled, inverted, knocked over or moved dynamically in any other way, then all screw holes should be utilized. 

 

 

             

           NEW LISTING 6/13/12
(click on above thumbnails to enlarge photos)
warranty
MACKIE 1620 ONYX MIXER W/ 'FIREWIRE' I/O OPTION CARD INCLUDED!
16 ANALOG / DIGITAL MIXING BOARD
#...3557
for sale
Great condition 16-Channel mixer by Mackie. Model 1620 mixer with optional 'FireWire' card already added! Excellent for many pro audio applications, including project recording studio, rehearsal / practice PA, Live Sound or Audio for Video use. This was use in a home music room for band rehearsal, so was never on the road or installed in a smoky bar. Looks near new!

Features:

- Analog mixer w/ Digital Capabilities (w/ USB Fire Wire Interface that's installed and included)
- ALL METAL 1/4" Jacks, mounted to the ACTUAL SHEET METAL!!!
- ALL XLR inputs / outputs each DOUBLE BOLTED to SHEET METAL!!!
- 16 Total channel inputs
- 8 new ONYX mic preamps with sound comparable to boutique preamps
- Output selectable up to full +4dB output level !!!
- XLR & 1/4" Balanced / Unbalanced (TRS or Sleeve Tip) Inputs on channels 1-8. 1/4" 'Unbalanced' (Sleeve-Tip) inputs on channels 9-16.
- 'Onyx' mic pre's on channels 1-8
- 4 AUX Sends w/ 4 'Stereo' returns that are each selectable 'Pre-Fade' / Monitor or 'Post' fader
- Individually switchable +48 volts Phantom Power (channels 1-8)
- 'Pre-Gain' control
- Individual channel LED Metering indicators for -20dB, 0dB, +10dB and OL (Clip) (always one of the most useful features on any mixer in my opinion)
- 75Hz Hi-Pass filter on each of the channels 1-8
- EQ 'In / Out' on each channel

- Two 'Tascam-standard' 8-track (not found on later Mackie 1620i mixer)
recorder outputs for DA-88, etc.
- 'Perkins EQ' circuitry. I don't know that I appreciate that too much, however, as far as channel EQ, on a mixer of this stature (meaning under $5 or $6k) it's got 4 bands of EQ on channels 1-8, with the 'Upper-Mids' and the 'Mid-Bass' bands being 'sweep-able'
- Individual Channel Muting (channels 9-16 feature standard 3-Band EQ)
- Individual Channel 'Solo' selectors
- 'Talk-Back' capabilities with either built-in / internal mic or XLR input for external mic.
- BNC connector for Little Light console lamp (not found on later Mackie 1620i mixing board)
- Rack mountable
- Primarily 'Metal' construction

Specs:
For Mackie 1620 specifications, see pdf on their web site here...  
  
From a 'web source', "The Mackie Onyx 1620i is a 16 Channel premium analog mixer with integrated 24-bit/96kHz FireWire I/O. The 1620i has 8 premium Onyx boutique-quality mic preamps, 4 band EQ with sweep-able mids on the mic channels and 3 band EQ with sweep-able mids on the stereo channels. The Firewire out lets you send a high quality signal to your DAW making live multi-track recording a snap, and there's flexible routing including Aux sends and pre/post eq routing available. There's Planet Earth power switching in this baby so you can take it anywhere in the world and it will play nice with the local power. And to that end, it's rack mountable as well."

"Onyx mixers another “world’s first” – an optional user-installable 24-bit/96kHz FireWire I/O card with the ability to..."Click here to go to Mackie's site for thorough info) 

From Mackies Web site, "FireWire I/O card, which provides up to 18 independent channels of 24-bit/96kHz audio and a stereo mix back to the Onyx mixer for monitoring. Plugs right into your FireWire-equipped Mac or PC. For those who record and produce music on computers, we’ve given Onyx mixers another “world’s first” – an optional user-installable 24-bit/96kHz FireWire I/O card with the ability to send up to 16 individual channels of high-quality digital audio direct to any FireWire-equipped computer (Windows XP or Mac OSX.3 or later). The FireWire card also sends a Left/Right stereo “quick mix” to the computer, with a level trim control that boosts or cuts the mix by ±10 dB as it is sent to the card — again letting you set levels independently for the live L/R mix and the recorded tracks."

"our new flagship Onyx mic preamps. These preamps build upon our already-impressive XDR design to meet or surpass expensive esoteric standalone mic pres in terms of fidelity, headroom and transparency—as well as..." Click here for more info

Here's an 'unbiased' review pdf page: http://www.mackie.com/pdf/press/
Onyx_1620_Rev_MusicTech.pdf

Again, this is a great condition, ONE OWNER Mackie 16-channel, Onyx 1620 mixing board. Includes optional FireWire I/O interface card already installed, official and optional rack-mount rails / ears and a pdf 'e' copy of owners manual.
Measures 17.5 without rack ears and standard 19" wide with x 20.5 front edge to rear edge and 6.5" thick. Weighs ~24 lbs unpacked. Includes our standard 30 day limited warranty.
MACKIE ONYX 1620 ANALOG MIXER W/ DIGITAL FIREWIRE I/O'S
Cond. 8.5
$399.
(Consignment) B. McW.

 

 

 

     

        NEW LISTING 4/18/13
 (click on above thumbnails to enlarge photos)
PRE-OWNED
DIGIDESIGN DIGI-002
RACK MOUNT 'PROTOOLS' INTERFACE
#...1808A
for sale
 One owner, DigiDesign, Digi002 Rack-Mount interface. Excellent for many pro-audio applications, including project recording studio, rehearsal / practice PA, Live Sound or Audio for Video use. This was use in a home music room for band rehearsal, so was never on the road or installed in a smoky bar. Looks near new!

Info from various web sites:

“Designed with both recording and performing musicians in mind, Digi 002 Rack is an affordable Firewire-based Pro Tools solution that packs all the punch of Digi 002 (minus the control surface) into a 2U rack-mountable unit. With Digi 002 Rack and Pro Tools LE software (not included), you'll have everything you need to create professional audio productions with the ease, power, and flexibility intrinsic to the Pro Tools family. And because it's FireWire-based, Digi 002 Rack offers portability that makes it equally viable for studio and live applications. Experience the power of Pro Tools in an all-in-one solution!”

 Again, this is a great condition, ONE OWNER DigiDesigns Digi-002 Rack-mount unit. Comes with a copy of the 'Getting Started' manual, Pro Tools LE software, version 6.2.3 for Mac OS X 10.3.2. and version 6.2.2 for 'Power Mac G5'. Measures 19.5” wide x 12.5” deep x 3.5” (2 rack spaces) tall. Weighs ~24 lbs unpacked.
DIGIDESIGNS DIGI-002 RACK
Cond. 8.5+
$99.
(Consignment) B. McW.
 
 

    

NEW LISTING 3/24/2023
(Click on above thumbnails to enlarge photos)

SERVICED / REFURBISHED BUT REMAINING ISSUE*
PRO TEAC MULTI-TRACK REEL TO REEL TAPE DECK
TASCAM SERIES
TEAC / TASCAM 34 4-TRACK TAPE DECK
4-TRACK / 4-CHANNEL STEREO / / MONO
3-HEAD / 2-SPEED (7.5 & 15IPS) / 3-MOTOR
10.5", 7" REELS AND / OR **SMALLER
MULTITRACK 1/4" TAPE DECK
#....3844
MIJ
for sale

See the entire listing for this deck on our "Reel to Reel Tape Deck" page...

 

    

NEW LISTING 1/11/2023
(Click on above thumbnails to enlarge photos)
  warranty
RESTORED / REFURBISHED / FULLY SERVICED
FOSTEX MULTI-8-TRACK REEL TO REEL TAPE DECK
FOSTEX MODEL 80
7" x 1/4" / 15ips TAPE DECK
3-HEAD / 3-MOTOR
REEL TO REEL 
MIJ
for sale

See the entire listing for this deck on our "Reel to Reel Tape Deck" page...

        

         NEW LISTING 1/6/2024
 (Click on above thumbnails to enlarge photos) 
warranty
PORTABLE SOUND SYSTEM / BUSKING / GUITAR AMP / PA SYSTEM / KARAOKE* DUAL 'HI-SPEED' CASSETTE TAPE DECK
"MUSIC MAESTRO SING ALONG AND RECORDING SYSTEM"
XL-100
#...0664
MADE IN KOREA (NOT China)
SOLD

Portable sound system / dual cassette tape deck / general purpose amp / speaker system / Busking / karaoke (*could be used as a "karaoke" machine, as long as you don't need 'video outs' for lyrics) all in one. This really is a ‘Swiss Army Knife’ of gear. We've used it for years as a keyboard / vocal / iPhone playback practice system (buy just graduated to something with a mixer for multiple keyboards). This thing is loaded!

Music Maestro Music System XL-100 Features:
- Dual cassette tape deck with ‘High Speed’ Dubbing (that actually does a great job)
- portable PA / sound system with built-in 25W+25W amplifiers
- Dual 5.75", full-range speakers with whizzer cones for extended top and
- Inputs for 1 or 2 microphones via 1/4" jacks
- Stereo AUX Input for guitar / keyboard / accordion, and with an small, cheap adaptor, most smart phones including an iPhone (that’s one thing I used it for).
- Rear located "Guitar" Input for guitar / keyboard / accordion etc.
Frankly, you could connect a mixer to the AUX, then connect even more things. The rear panel has Line In for another pre-amp or mixer and Line Output to go to another sound system, your computer to convert tapes to digital or to your stereo system to add cassette / keyboards / guitar / or microphones (be careful with your stereo speakers if you're going to do that).
- Rear located connectors for another, larger set of speakers on the rear panel (25 Watts x 2 and for either 4 or 8 Ohm speakers!).
- Built in “ECHO” effect for the microphones.
-  +- 12% 'Pitch Control' applicable to both decks
- 'Hi-Speed' applicable to both decks (Allows double speed playback, hi-speed recording and hi-speed fast wind)
- Tape type selectors
- AMS (Automatic Music Search) fast wind thru up to 9 selections to find songs (must have at least 3 seconds of silence between songs for this to work properly)

EVERYTHING works!!! We've tested it all. Controls are still clean. NO broken or missing knobs. Both deck wells open and close. All tape transport functions work on both decks. NO dragging, sluggishness or eating tapes.
 Both cassette decks actually sound very good (even compared to another deck (‘mid-end’ Technics) I have that was recently restored). Again, the ‘Hi-Speed dubbing’ button also does two other things. For either deck, it kicks the fast wind into “high speed”. It also works in ‘Record’ mode so you can record at double tape speed to increase quality (plus you also have the ‘Pitch Control’ to add an additional 12% if desired). It also can double ‘Playback Speed’ so if you use the deck to transfer your cassettes to computer / digital files, you can cut your time in half.  Measures 18" tall x 14" wide x 10.5" deep and weighs 26 lbs unpacked.
Made in Korea (not china).
$249.
SOLD

 

POWER AMPS / AMPLIFIERS


 

    

NEW LISTING 4/22/2021
(Click on above thumbnails to enlarge photos)
warranty
BENCH CHECKED / TESTED / CLEANED / WARRANTED
RAMSA WP-1400 (Their BIG one)
PROFESSIONAL
STEREO POWER AMPLIFIER
#...0037
400W+400W STEREO
800 WATTS MONO
MIJ
for sale
We have complete gone through this unit and bench checked / tested it. Amp has been cleaned inside and out including both attenuators. All functions have been tested and pass with flying colors! Amp designed using Huge Power Supply Transformer and a very efficient Dual "wind tunnel" heat sink, for directing fan driven forced air for cooling from dual cooling fans. This amplifier is in both great electronic and physical shape. Looks NEAR NEW and sounds fantastic! All inputs tested and both side produces clean and even sine waves! No power supply hum of any kind. It's dead silent! Following restoration procedures, we burned it in, in the shop at continuous high volume for 4 hours straight, then a further 100 hours at lower volumes and it functioned flawlessly.

I worked for a Ramsa dealer for many years and spec'd Ramsa gear in many pro-audio installations, including a few at the USAF Academy here in Colorado Springs.  
  
On our test bench, this particular, #...0037, unit's amplifiers produced 50 Volts at 8 Ohms per channel for 312 Watts / channel & 36 Volts at 8 Ohms per channel for 324 Watts / channel all tests @ 1kHz into a 'brick wall' load.

Ramsa SP-1400 Features:

- Ultra-low-noise/ low-distortion design
- Stereo or Bridge Mono Operation
- Multi mode protection; Thermal Protection, Power Initiation Protection & DC protection
- Balanced XLR and TRS 1/4" plugs
- 1/4" jacks and 5-way binding post outputs
- Power On, Protect and Peak LEDs
- Dual Wind Tunnel, Forced Air Cooling w/ Auto-adjusting air speed
- 3-U Rack Space Design
- Both front rack ears as well as mounting ears in the rear for rear mounting amp in road  racks & flight cases

Ramsa WP-1400 Specifications / Specs:

Output Power: (Typical value) Stereo mode, both channels driven
4 Ohms, 1 kHz, .1 THD - 240 WRMS per channel
8 Ohms, 1 kHz, .1 THD - 400 WRMS per channel
Bridge mode, mono: 8 Ohms, 20 Hz to 20 kHz,0.02% THD - 800 WRMS
Voltage gain: 30.3dB
Input Sensitivity and Impedance: Input attenuator set @ FCW @ rated output power / 4 Ohms = +4dBu
Balanced, 1/4" phone TRS jack
Balanced XLR

Frequency Response: (Typical) Stereo mode, both channels driven
+0,-0.5 dB, 1 WRMS, 4 Ohms - 20Hz to 20kHz
Damping Factor: (Typical value) Stereo mode, both channels driven 8 Ohms, 1 kHz - Greater than 100
Hum and Noise: Stereo mode, both channels driven
Below rated output power, 4 Ohms - >100 dB, un-weighted
THD: Stereo mode, both channels driven
 @ 8 Ohms / 240W+240W = ≤0.3% THD.
 @ 8 Ohms / 400W+400W = ≤0.3% THD.
Crosstalk: >60dB
POWER CONSUMPTION: 1550 Watts in Stereo mode, both channels driven @ 400 Watts @ 4 Ohms & @ 120 VAC
WEIGHT: 38.2 lbs. (17.4 kg)

Great condition pro audio power amp by Ramsa. Model WP-1400. Excellent for most pro audio applications. This was use in a home music room for band rehearsal, so was never on the road or installed in a smoky bar. Looks near new! Lots of punch and headroom.

On our test bench, both amplifiers produce perfectly clean and symmetrical sine waves at both 8 & 4 ohm loads. We tested both internal amplifiers to the above specs, and found them accurate.
This is a great performing, fan cooled amp. Huge power from a company know for building "rock solid", VERY dependable gear. Again I was a Ramsa dealer for years, and the stuff RARELY broke. Period!
Comes with an "e-copy / pdf download" of the Ramsa WP-1400 owners / users / instruction manual and one of the original brochure if the purchaser desires.
 Measures 19" wide x 16" rack depth x 3.5" tall and weighs 39 lbs unpacked. Includes our standard 30 day limited warranty.
PANASONIC / RAMSA WP-1400
 Cond. 8.5++
NEW MSRP - $840.00
PRE-OWNED
$439. (C)
R.R.

(Above text, in it's entirety, property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)

  

         NEW LISTING 8/27/09
(click on above thumbnails to enlarge photos)
warranty
BENCH CHECKED / TESTED / CLEANED / WARRANTED
PEAVEY GSP-1500
PROFESSIONAL
STEREO POWER AMPLIFIER
1500 WATTS!
#...8698
STABLE AT 2 OHMS!
MADE IN THE USA!
for sale
We have complete gone through this unit and bench checked / tested it. Amp has been cleaned inside and out including both attenuators. All functions have been tested and pass with flying colors! Amp designed using Huge, Torroidial design, Power Supply Transformer and a very efficient Dual "wind tunnel" heat sink, for directing fan driven forced air for cooling from dual cooling fans. This amplifier is in both great electronic and physical shape. Looks LIKE NEW and sounds fantastic! All inputs tested and both side produces clean and even sine waves! No power supply hum of any kind. It's dead silent! Following restoration procedures, we burned it in, in the shop at continuous high volume for 4 hours straight and it functioned flawlessly.

I worked for a Peavey dealer for many years and have toured about 25 of their plants in MS and I consider this series to be the best, overall power amp they did. I have installed many in clubs, churches and touring rigs with total confidence. I knew when I installed one, it was going to stay "gone" and keep working strong.  
  
  On our test bench, this particular, #...8698, unit's amplifiers produced 52.5 volts at 8 ohms per channel for 344 continuous watts / channel before the DDT auto clipping circuit kicked in with our sine wave generator, via 32 total discrete output transistors. 

Features:

- Ultra-low-noise/ low-distortion design
- Stereo or Bridge Mono Operation
- Multi mode protection; Thermal Protection, Power Initiation Protection, DC protection, Loud Fault protection, Short Circuit protection and DDT for clipping protection,
- De-featable DDT Compression
- XLR thru I/O's that accommodate 1/4" plugs
- 1/4" jacks and 5-way binding post outputs
- Power On, Signal Present and DDT LEDs
- Reportedly, easily handles 2-ohm loads all night long
- Dual Wind Tunnel, Forced Air Cooling
- Compact, 2-U Rack Space Design
- Both front rack ears as well as mounting ears in the rear for rear mounting amp in road  racks & flight cases

Specs:

Output Power: (Typical value) Stereo mode, both channels driven
2 Ohms, 1 kHz, .1 THD - 750 WRMS per channel
4 Ohms, 1 kHz, .1 THD - 550 WRMS per channel
8 Ohms, 1 kHz, .1 THD - 320 WRMS per channel
Bridge mode, mono
4 Ohms, 1 kHz, .1 THD - 1,500 WRMS
8 Ohms, 1 kHz, .1 THD - 1,100 WRMS
Rated Output Power: Stereo mode, both channels driven
4 Ohms, 20 Hz to 20 kHz,0.03% THD - 500 WRMS per channel
8 Ohms, 20 Hz to 20 kHz,0.02% THD - 280 WRMS per channel
Slew Rate: (Typical value)
Stereo mode, each channel - 40 Volts per usec
Bridge mode, mono - 80 Volts per usec
Input Sensitivity and Impedance:
Input attenuator set @ FCW
@ rated output power, 4 Ohms - 1.17 VRMS (+1 dBV)
Unbalanced, 1/4" phone jack - 20 k Ohms
Balanced, XLR (phase selectable) - 10 k Ohms per leg
Overall system gain per channel - 40X (+32 dB)

Frequency Response: (Typical) Stereo mode, both channels driven
+0,-1 dB, 1 WRMS, 4 Ohms - 5 Hz to 50 kHz
+0,-0.2 dB @ rated output, 4 Ohms - 20 Hz to 20 kHz
Damping Factor: (Typical value) Stereo mode, both channels driven
8 Ohms, 1 kHz - Greater than 400
Hum and Noise: Stereo mode, both channels driven
Below rated output power, 4 Ohms - 100 dB, un-weighted
POWER CONSUMPTION: Stereo mode, both channels driven @ 1/8 rated power @ 2 Ohms - 1080 Watts @ 120 VAC
WEIGHT: - 39.2 lbs. (17.9 kg)

  Great condition pro audio power amp by Peavey. Model GPS-1500! Excellent for most pro audio applications. This was use in a home music room for band rehearsal, so was never on the road or installed in a smoky bar. Looks near new! Lots of punch and headroom.

On our test bench, both amplifiers produce perfectly clean and symmetrical sine waves at both 8 & 4 ohm loads. We tested both internal amplifiers to the above specs, and found them accurate.
 This is a great performing, fan cooled amp. Huge power from a company know for building "rock solid", VERY dependable gear. Again I was a Peavey dealer for years, and the stuff RARELY broke. Period! 
 Measures 19" wide x 16" rack depth x 3.5" tall and weighs 40 lbs unpacked. Includes our standard 30 day limited warranty.
 PEAVEY GSP-1500
 Cond. 8.5++
NEW MSRP - $1300.00
PRE-OWNED
$379.
 

         NEW LISTING 8/27/09
(click on above thumbnails to enlarge photos)
warranty

BENCH CHECKED / TESTED / CLEANED / WARRANTED
MACKIE M-1400i
STEREO POWER AMPLIFIER
PROFESSIONAL "FR" SERIES
UP TO 1400 "REAL WATTS"
#...7113
STABLE AT 2 OHMS!
MADE IN THE USA!
Circa 1997
for sale
  We have complete gone through this unit and bench checked / tested it. Amp has been cleaned inside and out including both attenuators. All functions have been tested and pass with flying colors! Amp designed using Huge, Torroidial design, Power Supply Transformer and a very efficient "T" shaped "wind tunnel" heat sink, for directing fan driven forced air for cooling. This amplifier is in both great electronic and physical shape. Looks LIKE NEW and sounds fantastic! All inputs tested and both side produces clean and even sine waves! No power supply hum of any kind. It's dead silent! Following restoration procedures, we burned it in, in the shop at continuous high volume for 4 hours straight and it functioned flawlessly.
  
  On our test bench, this particular, #...7113, unit's amplifiers produced 47 volts at 8 ohms per channel for 276 continuous watts / channel before the auto clipping circuit kicked in with our sine wave generator, via 16 total, 8 each MJL21193 & MJL21194 discrete output transistors. 

From the spec sheet; "The M•1400/M•1400i is rated at a continuous out­put of 250 watts per channel into 8Ω, 425 watts per channel into 4Ω and 630 watts into 2Ω. In bridge mode the M•1400/M•1400i is rated at 850 watts into 8Ω and 1260 watts into 4Ω......Variable low-cut filters on each channel, with a range from off to 170Hz, enable tighter bass response and a Constant Directivity Horn EQ improves high-frequency reproduction. The CD Horn EQ is 6 dB/octave and its "knee" position is sweep-able from 2kHz to 6kHz. The built-in limiter is channel independent and helps eliminate clipping. Inputs are balanced/unbalanced 1/4" and XLR, and XLR thru connectors."

Features:

- Ultra-low-noise/ low-distortion design
- "FR" / Fast Recovery circuitry reduces distortion at the edge of clipping and beyond
 - Two 2nd order, 12dB/octave, Bessel low-cut filters with variable frequency from Off to 170Hz help optimize bass output of your sound system
- 3rd order, 18dB/octave, Bessel electronic subwoofer crossover with two selectable frequency points
- Constant directivity horn EQ/Air EQ with variable frequency from 2k to 6kHz and on/off switch
- Limiter with On/Off switch (decreases distortion that may become present when the M1400i is driven at max levels without affecting overall sound levels)
- XLR thru I/O's that accommodate 1/4" plugs
- 1/4" jacks and 5-way binding post outputs
- De-tented gain controls calibrated in dB's & volts
- Signal Present and Clip LEDs
- Channel Status LEDs
- Reportedly, easily handles 2-ohm loads all night long
- Superior T-Design cooling (The "wind tunnel" thing we were talking about earlier)
- Compact, 2-U Rack Space Design
- Both front rack ears as well as mounting ears in the rear for rear mounting amp in road  racks & flight cases

Specs:
Continuous AVG power output and THD;
250 watts per channel into 8 ohms from 20Hz to 20kHz, with no more than 0.012% THD
425 watts per channel into 4 ohms from 20Hz to 20kHz, with no more than 0.025% THD
630 watts per channel into 2 ohms from 20Hz to 20kHz, with no more than 0.050% THD
Max Power Ratings:
- 300 + 300 watts @ 8 ohms stereo
- 500 + 500 watts @ 4 ohms stereo
- 700 + 700 watts @ 2 ohms stereo
- 1000 watts @ 8 ohms bridged
- 1400 watts @ 4 ohms bridged
Power Bandwidth: 20Hz to 70kHz (+0, –3 dB)Frequency Response: 20Hz to 40kHz (+0, –1 dB
10Hz to 70kHz (+0, –3 dB)
Signal to Noise Ratio: >107 dB below rated power into 4 ohms
Channel Separation: >80 dB @ 1kHz
Slew Rate: Voltage Slew Rate >50V/μs >100V/μs bridged Current Slew Rate >32A/μs at 2Ω
Damping Factor: >350 from 0 to 400Hz
Input Impedance: 20kΩ balanced bridging
Input Sensitivity: 1.23 (+4 dBu) for rated power into 4 ohms
Voltage Gain: 30.25 dB (32.5V/V)
Maximum Input Level: 9.75 volts (+22 dBu)
Rise Time: <4.4μs
CMRR: >40 dB, 20Hz to 20kHz
Transient Recovery: 1μs for 20 dB overdrive at 1kHz
Variable Low-Cut Filter: 10Hz (Off) to 170Hz, 2nd Order Bessel
Subwoofer Low-Pass Filter: Switched: 63Hz/125Hz, 3rd Order Bessel
Constant Directivity High-Frequency Boost: 2kHz to 6kHz (+3 dB points)6 dB/octave high-frequency shelving filter, (shelving occurs at approximately 30kHz)
Limiter Section: Complementary Positive and Negative Peak Detecting
Indicators: 6 meter LEDs per channel SIG (Signal Present), –20, –9, –6, –3, OL (Overload) PROTECT LEDs, CH1 & 2SHORT LEDs, CH1 & 2TEMP STATUS COLD/HOT LEDs
Power Consumption:
65 watts (0.9A) at idle
550 watts (6.7A) with musical program fully loaded (4 ohms per side, or 8 ohms bridged)
900 watts (10.5A) with musical program fully loaded (2 ohms per side, or 4 ohms bridged)
850 watts (9.6A) at full power into 8 ohms (continuous sine wave)
1500 watts (15.6A) at full power into 4 ohms (continuous sine wave)
2500 watts (24.8A) at full power into 2 ohms (better have a strong AC circuit for those last two scenarios)
  
  Great condition pro audio power amp by Mackie. Model M-1400i from their "FR" series. HUGE power output! Excellent for most pro audio applications. This was use in a home music room for band rehearsal, so was never on the road or installed in a smoky bar. Looks near new! Lots of punch and headroom.

"The Mackie M1400i amplifier provides up to 1400 watts of clean power using the very latest technology. Sonic quality rivals the most expensive audiophile power amps on the planet, with Total Harmonic Distortion of just 0.012% at 8 ohms 20- 20kHz."

On our test bench, both amplifiers produce perfectly clean and symmetrical sine waves at both 8 & 4 ohm loads. We tested both internal amplifiers to the above specs, and found them accurate.
This is a great performing, fan cooled amp.
Measures 19" wide x 16.5 overall depth / 16.5" rack depth x 3.5" tall and weighs 36 lbs unpacked. Includes our standard 30 day limited warranty.
MACKIE FR M-1400i
Cond. 8.5++
$299.
 

 

    

      NEW LISTING 4/19/13
(click on above thumbnails to enlarge photos)
warranty
VINTAGE FOSTEX SPRING REVERB
FOSTEX 3180
 STEREO ANALOG "SPRING" REVERB
 Circa 1980's
M.I.J.
for sale
We have completely gone through it cleaning and testing everything. Power and all display lamps replaced with new units for years of trouble free service. All send and receive coils in perfect, working order. All internal controls, switches and pots cleaned and are quiet. I/O jack solder joints inspected. Unlike my 'personal' Fostex 3180 reverb, this one has ALL the original, colored 'knob inserts' intact (they are commonly missing). Works and sounds great.
 _____________________________________
 
Classic sounding, Analog Spring Reverb by Fostex. This is a great unit for about any 'studio' application. Would also work in some SR / PA / Guitar apps as well, as long as you mind the I/O levels. Has very strong send and receive coils on the reverb tank, so you can get HUGE reverb with this one if you wish. Also great for use in your studio. Silk-screened chart on bottom shows a variety of hook-ups. While this unit would be 'rack-mountable' with optional rack mount ears / hardware, none are included. Unit measures only 17" wide x 7.5" deep x 3.5" tall and weighs ~5 lbs unpacked. Comes with our 30 day limited warranty.
FOSTEX 3180 ANALOG SPRING REVERB
 Cond. 8
$499. 

 

    

NEW LISTING 3/12/19
 (Click on above thumbnails to enlarge photos) 
  warranty
PRE-OWNED
BEHRINGER MODULIZER PRO DSP1224P
#...5125
Designed in Germany / M.I.C.
for sale

Features:

- Cutting edge effects such as 3D Processor, Stereo Imager, Lo-Fi, Super Bass, Ring Modulator, Voice Canceler etc.

- 24 breathtaking effects such as Ultra Phaser, Harmonic Exciter, Auto Filter, Jetstream Flanger, Ultra Compressor, Guitar Combo, Speaker Emulation, Resonator and more

- Hundreds of effect variations plus two individual parameters and separate low and high EQ section

- True stereo processing performance allows separation of left and right channels in the stereo field for open sounding enhancement of the sound sources

- Free MODULIZER design software allows for total remote control via PC (download at www.behringer.com)

- 24-bit A/D and D/A converters with 64/128 times oversampling for ultra-high headroom and resolution

- Internal 24-bit processing with professional 46 kHz sampling rate

- Servo-balanced inputs and outputs on gold-plated XLR and TRS connectors for high signal integrity

- 100 user-preset memories to store programs for instant recall

- Accurate 8-segment LED level meters simplify level setting for optimum performance

- "Future-proof" software-upgradeable architecture

- Full MIDI capability allows real-time parameter control and program selection

- Internal power supply design for professional application

- High-quality components and exceptionally rugged construction ensure long life

- Designed and engineered in Germany

This is from our personal studio and we have thoroughly tested this Behringer, DSP1024P, Multi-Effects unit (just changing out some of our newer, cleaner gear for some older, and frankly 'more beat up' gear).
Standard 19" rack mount width and a single space high.
Includes a pdf / e-copy of the Behringer Modulizer Pro DSP1224P owners / users manual.
Includes our standard 30 day limited warranty. 
BEHRINGER MODULIZER PRO DSP1224P
Cond. 9
$129.

 

 

    

NEW LISTING 3/12/19
 (Click on above thumbnails to enlarge photos) 
  warranty
PRE-OWNED
BEHRINGER VIRTUALIZER PRO DSP1024P
#...9123
Designed in Germany / M.I.C.
for sale

Features:
- “Wave-Adaptive Virtual Room” reverb algorithms calculated from precise mathematical room models give you ultra-natural reverb effects

- 32 breathtaking effects such as Reverb, Chorus, Flanger, Delay, Pitch Shifter, Vocoder and Rotary Speaker

- More than 700 effect variations plus 2 individual parameters and separate low and high EQ section

- 2 digital processing engines offer individually deployable or coupled effects on left and right channels

- True stereo-processing performance allows separation of left and right channels in the stereo field for open-sounding enhancement of sound sources

- Free VIRTUALIZER Design software allows for total remote control via PC (download at www.behringer.com)

- 24-bit A/D and D/A converters with 64/128 times oversampling for ultra-high headroom and resolution

- Internal 24-bit processing with professional 46 kHz sampling rate

- Servo-balanced inputs and outputs on gold-plated XLR and ¼” TRS connectors

- 100 user preset memories for storing programs for instant recall

- Accurate 8-segment LED level meters simplify level setting for optimum performance

- “Future-proof” software-upgradeable architecture

- Full MIDI capability allows real-time parameter control and program selection with "IN", "OUT" and "THRU" jacks

- Selectable +4dBu or -10dBV I/O Operating levels

- Internal power supply design for professional application

- High-quality components and exceptionally rugged construction ensure long life

Designed and engineered in Germany

This is from our personal studio and we have thoroughly tested this Behringer, DSP1024P, Multi-Effects unit (just changing out some of our newer, cleaner gear for some older, and frankly 'more beat up' gear).
Standard 19" rack mount width and a single space high.
Includes a pdf / e-copy of the Behringer Virtualizer Pro DSP1024P owners / users manual.
Includes our standard 30 day limited warranty. 
BEHRINGER VIRTUALIZER PRO DSP1024P
Cond. 9
$99.

 

NEW LISTING 10/22/2024
NEI XMP
MIXER / MIXING BOARD POWER SUPPLY
INFO, PRICE AND PHOTOS COMING
for sale
 

(click on above thumbnails to enlarge photos)
warranty
DIGITECH
RDS-2000
DIGITAL DELAY
MADE IN THE USA!
for sale
Very useable delay for PA, studio, or instruments. We use these in our systems for general purpose slap-back on the vocals and acoustic guitar, but they will go up to 2 seconds.
Features:
- Range 0ms to 2000ms
- Signal, Clip and Bypass LED's
- Controls; Speed, Width, Delay Time, Delay Range, Feedback, Mix, Output Level and Input Level
- Tepean / Hold/ Trigger / Sample switch
- 1 Rack Space in height
- Rackmountable

Unit has "real pots" so you can set them instantly, and it stays with out having to pick a program patch, or hit store. Great Delay, Chorus and Flange effects. Unit pre-owned. Includes our 30 day limited warranty. Works great!
DIGITECH RDS-2000 DIGITAL DELAY
Cond. 8.5
$189.
HOLD FOR SHOP USE.
  

       

 
 

          NEW LISTING 9/20/12
(click on above thumbnails to enlarge photos)
warranty
PRE-OWNED
DBX 1215 EQ
2/3 OCTAVE
PROFESSIONAL
GRAPHIC EQUALIZER
#...4718
for sale
Great condition, One-Owner, dbx 1215 Equalizer. From the dbx website; "The dbx® 12 Series were designed to meet the needs of the most demanding sound reinforcement environments, while offering the simplicity of straightforward controls. The 1215 provides standard features like dual channels, 15 2/3 octave bands, ISO frequency centers, +/-12 dB input gain range, and switchable 40Hz/18 dB per octave low-cut filters, but also includes other thoughtful features. These include 45 mm faders; selectable +/-6dB or +/-15dB boost/cut range for precise gain adjustments; XLR, barrier strip, and 1/4'' TRS connectors for installation ease; balanced inputs and outputs for quiet operation; and chassis/signal ground lift capabilities for quick hum isolation. The visionary design of the dbx 12 Series makes your job easier.
The dbx 12 Series Equalizers were precision engineered to provide years of maintenance-free operation in any application. The magnetically isolated transformer, electronically balanced/unbalanced inputs and servo balanced/unbalanced outputs, RF-filtered inputs and outputs, and power-off hard-wire relay bypass with 2 second power up delay were steps our engineers took to ensure compatibility for all installations. Only the best components were utilized, yielding a 10Hz to 50kHz frequency response, greater than 90dB SNR (ref +4dBu), less than 0.005% THD +Noise (1kHz at +4dBu), and inter-channel crosstalk of less than -80dB from 20Hz to 20kHz. All this attention to detail is contained in a 2U steel/aluminum chassis."  

Features:

- Dual 15 band, Graphic EQ - 15 frequency centers are as follows starting at the low-end: 30Hz - 63Hz - 110Hz - 190Hz - 330Hz - 580kHz - 1kHz - 1.7kHz - 3kHz - 5.2kHz - 9kHz & 16kHz.
- Switchable boost/cut ranges of ±6 or ±15 dB
-Electronically balanced/unbalanced inputs
- Servo balanced/unbalanced inputs
- RF filtered inputs and outputs
- XLR, Barrier Strip, and 1/4" TRS I/O connectors W/ Shaft nuts on 1/4" jacks and dual mounting bolts on the XLR's, directly to sheet metal.
- 12dB/+12dB input gain range
- 18dB/octave 40Hz Bessel low-cut filter
- Chassis/signal ground lift capability
- Power-off hardwire relay bypass with 2-second power-up delay

dbx 1215 EQ Specifications:

Inputs: Connectors: 1/4" TRS, female XLR (pin 2 hot), and barrier terminal strip
Input Type: Electronically balanced/unbalanced, RF filtered
Input Impedance: Balanced 40kΩ, unbalanced 20kΩ
Max Input Level: >+21dBu balanced or unbalanced
CMRR: >40dB, typically >55dB at 1kHz
Outputs: Connectors: 1/4" TRS, male XLR (pin 2 hot), and barrier terminal strip
Output Type: Impedance balanced/ unbalanced, RF filtered
Impedance: Balanced 200 Ω, unbalanced 100Ω
Max Output Level: >+21dBu balanced/unbalanced into 2k½ or greater >+18dBm balanced/unbalanced (into 600Ω)
Bandwidth: 20Hz to 20kHz, +0.5/-1dB
Frequency Response: <10Hz to >50kHz, +0.5/-3dB
Dynamic Range: 115db
Signal-to-Noise: 97db
THD: <0.005%
Inter-channel Crosstalk: <-80dB, 20Hz to 20kHz Function Switches
Low Cut: Activates the 40Hz 18dB/octave Bessel high pass filter
Range: Selects either +/- 6dB or +/- 15dB slider boost/cut range
Indicators Output Level: 4-LED bar graph (Green, Green, Yellow, Red) at -10, 0, +10, and +18dBu EQ Bypass LED: red Clip: 1 LED: red Low Cut: 1 LED: red +/-6dB: 1 LED: yellow +/-15dB: 1 LED: red Power Supply
Operating Voltage: 100VAC 50/60Hz, 120VAC 60Hz, 230VAC 50/60Hz
Power Consumption: 24W
Mains Connection: IEC receptacle Physical

Great condition pro audio power EQ by DBX. Model 1215! Excellent for most pro audio applications. This was use in a home music room for band rehearsal, so was never on the road or installed in a smoky bar. Looks near new!

 This is a great performing EQ. Huge power from a company known for building high quality, VERY dependable gear. Dimensions: 3.5" H X 19" W X 7.9"D Weight: 8.5 lbs.
 Includes our standard 30 day limited warranty.
 DBX 1715
 Cond. 8.5++
NEW MSRP - $400.00
PRE-OWNED dbx 1215 2/3 Octave graphic EQ
$239.
(Consignment) B. McW.

 

 

            NEW LISTING 8/27/07
(click on above thumbnails to enlarge photos)
warranty
ALESIS
MICROGATE
EFFECTS UNIT
MADE IN THE USA
for sale
Great utility Noise Gate. I keep a couple of these in my “tool box” for inserting into channels. Great for snare Features:
- 1/3 width rack space
- Stereo I/O's
- Open, Delay and Close LED's
- Trigger input for timing with other signals
- Controls; Threshold, Delay Time, Rate
- Bypass switch
- 1 Rack Space in height
- Rack-mountable with rack shelf (not included)

Great for kick drum & electric guitar, especially when players are using noisy, effects.

1/4" in and out, with a 1/4" jack for a footswitch to defeat the effect. Comes with AC power adaptor. Pre-owned. Includes our 30 day limited warranty. Works great!
ALESIS MICROGATE
Cond. 8.5
$79.

NEW LISTING 11/26/07
(click on above thumbnails to enlarge photos)
warranty
FURMAN
X-324 X324
STEREO 2-WAY / MONO 3-WAY
ELECTRONIC CROSSOVER
MADE IN USA!
for sale
Of all the crossovers out there, Furman are some of the most sought after and certainly professional you will use. Comparable to Brooks Siren or White. Full 24dB / Oct and on this particular unit a full 24dBv!!! (don't know what that means? research it or go ahead and stick with a cheap, Chinese Behringer / Soundtech / Audio-Centron / etc.) If you're an audio pro, you didn't need any of that info anyway, but had to get it out of the way, since I have recently read some fairly humorous / ill-informed blogs on the web.
     Anyway, on to the unit. It's a Furman X-324B, Stereo 2-way / Mono-3-way, Balanced I/O, crossover. I was a Furman dealer (yes, Behringer, Yamaha, Peavey, Crate, DOD, Digitech, Alesis, Crest, Fender, QSC, Crown, EV, and about 30 others I can't think of now) and anytime I was putting together a serious rig for a client or myself, it was filtered through a Furman "Balanced" x-over.

Ok, This one get's pretty wordy, so here's a link to it's own page:

http://www.oaktreevintage.com
/furman_x-324_crossover.htm 


 

 

NEW LISTING 11/26/07
(click on above thumbnails to enlarge photos)
warranty
FURMAN
TX-3 TX3
STEREO 2-WAY / MONO 3-WAY
ELECTRONIC CROSSOVER
MADE IN USA!
for sale
Good condition and still very "useable", Furman, TX-3 crossover. Great for club / church / band systems using 1/4" connections. "Old School" construction, made in the USA!
Features:

- Variable Input levels for both channels
- Frequency Range Selectors; X1, X10, X100
- Crossover Frequency Rotary's from arbitrary 15-250
- 4x Output level controls (for both mono or stereo operation)
- 1/4" I/O's

Units has been fully bench tested. Not too pretty cosmetically, but works fine. Great for smaller / simpler systems or as a monitor filter / x-over. Easy to use. 3-prong, Grounded AC cord. Standard single rack space and 8" deep. Includes our 30 day limited warranty. Works great!
FURMAN TX-3
Cond. 8
$129.

(click on above thumbnails to enlarge photos)
warranty
PEAVEY
EQ-215
EQUALIZER
DUAL 15 BAND EQ
MADE IN USA!
for sale
Great for general purpose EQ uses, especially your club mains, or for mixing you monitors for "line level" devices. Very flexible patch panel. Processes a full 24dBv of signal, (as opposed to only +18dBv of signal most eq's and processors are capable of).

Features:
- +-6 or +-12 dB operation
- Built-in low cut filter  
- Built-in Hi-Cut filter
- Balanced XLR And 1/4" inputs and outputs
- 1 Rack Space in height
- Full 24dBV  input and output operating levels
- Huge gain and very quiet!
- Rackmountable

Dual bolted XLR jacks and shaft nuts on all the phono inputs! 1 rack space. Pre-owned. Works great! Includes our 30 day warranty.
PEAVEY
EQ-215
COND. 8.5
$159.

   

 

NEW LISTING 7/5/07
(click on above thumbnails to enlarge photos)
warranty
PRE-OWNED
SOUNDTECH
12", 2-WAY WEDGE STAGE MONITOR
for sale
Cab & grill are in good shape. We have completely tested them including sweeping them with an audio generator looking for any acoustical anomalies or extraneous noises or sounds. We removed the typically, troublesome hi-freq attenuator / L-pad for more reliable top end. These have a "real" crossover and a "real" horn driver for the top-end. They work and look great!

Specs:
Drivers; 12" Woofer / Foster 90° x 60° Exponential horn
Input Connections; Dual 1/4" Phone jacks
Finish; Black Ozite Carpet

Great performing 12" wedge monitor for lower budgets. Great for clubs, small groups, church, etc. Expanded metal grill for durability and speaker protection. Made in USA! Each measures 16" high x 21" wide x 18" deep and weighs 30 lbs unpacked. Includes our standard 30 day limited warranty ( excluding problems due to under / over powering).
Cond. 8.5
SOUNDTECH 12" , 2-way Stage Monitor
$139. ea
1 left



 

   

 

NEW LISTING 7/5/07
(click on above thumbnails to enlarge photos)
warranty
PRE-OWNED
PEAVEY
112M
12", 2-WAY WEDGE STAGE MONITOR
for sale
Cab & grill are in good shape. We have completely tested them including sweeping them with an audio generator looking for any acoustical anomalies or extraneous noises or sounds. They work and look great!

Specs:
Drivers; 12" Woofer / Piezo Radial horn Tweeter
Input Connections; Dual 1/4" Phone jacks
Controls; Hi-Freq Attenuator
Power Handling; 65 RMS watts
Finish; Black Durafleck

Great performing 12" wedge monitor for lower budgets and lighter weight. Great for clubs, small groups, church, etc. Perforated metal grill for durability and speaker protection. I sold these for years as a Peavey dealer. Even at twice the price they would be a great value. Great punch and cuts through high stage volumes! Made in USA! Each measures 12" high x 18.5" wide x 16" deep and weighs 21 lbs unpacked. Includes our standard 30 day limited warranty ( excluding problems due to under / over powering).
Cond. 8.5
PEAVEY 112M
$79. ea
1 left

 

     

(click on above thumbnails to enlarge photos)
warranty
JENSEN
JP-1200
PA / DJ / STEREO SPEAKERS
for sale
Decent sounding 3-way DJ / Stereo speakers. Horn mids and tweeters. 
Other Features include:

- 8” woofer w/non-deteriorating butyl rubber surround
- 4.5” X 10.25” piezo horn mid
- 2.5" piezo horn tweeter
- Dual 2.5" tuned ports for extended bass
- 8 Ω
- Spring loaded speaker connectors

Covered in black Ozite carpet, these cabinets sport handy inset handles and plastic bumper corners with only normal wear and tear.  We have used these for a couple of DJ gigs and they impressed. All drivers work and sound fine! Tested for all frequencies with a sweep generator. Speakers look and sound GREAT! Each measures 22" tall x 12" wide x 10.5" deep and weighs 20 lbs unpacked. Includes our standard 30 day limited warranty ( & excluding problems due to under / over powering)
JENSEN JP-1200
Cond. 9
$119. pair

 

(click on above thumbnails to enlarge photos)
warranty
USED 
CRATE
OLD SCHOOL/VINTAGE
       CRATE EX-P1 / EXP1
SPEAKER CABINET
Circa 1980-82
for sale
These Crate EX-P1's sport an authentic "Dynamite box" construction of solid pine.  Features include:

- 12" woofer with non-deteriorating "accordion" paper surrounds
- Black metal grills
- 8Ω rating
- 40 Watts
- Parallel .25" I/O's

These speakers have been completely checked out and work great. Each measures 19" h  x 17.5" w x  10" d and weighs 25 lbs unpacked. Includes our 30 day warranty (excluding problems due to under / over powering)
Crate
EX-P1
Cond. 8.5
$149. ea. 2 Remaining in stock
(HOLD FOR SHOP USE)

 

(click on above thumbnails to enlarge photos) 
warranty
USED 
CRATE
OLD SCHOOL/VINTAGE
      CRATE PB-1 / PB1
HORN BANK
Circa 1981-83
for sale
These Crate PB-1's sport an authentic "Dynamite box" construction of solid pine.  Features include:

- 2 Piezo Radial horn Tweeters
- 1 Piezo Horn Mid
- No impedance.
- 40 Watts
- Parallel .25" I/O's

These speakers have been completely checked out and work great. Each measures 17.5" w x 6.5" h x  7" d and weighs 8 lbs unpacked. Includes our 30 day warranty (excluding problems due to under / over powering)
Crate
PB-1
Cond. 8.5
$99. 1 Remaining in stock
(HOLD FOR SHOP USE)

 

    

               NEW LISTING 6/21/07

(Click on above thumbnails to enlarge photos)
warranty
HORIZON / RAPCO
16 X 4 X 100'
UN-POWERED SNAKE
"STAGE SERIES"
for sale
Used for 3 club shows! Like new condition. 20 channels, 16 XLR sends x 4 TRS, 1/4" returns. All sends and returns are 2 pair, 24g, 100% foil shielded with gnd. As it's 100% foil shielded, it is VERY efficient at rejecting RFI (means you won't be picking up any country stations through your PA, due to the snake). All the XLR jacks are double riveted to the steel box, and the 1/4" returns feature locks. We also did some of our standard custom mods we have done to most of the new snakes we have ordered throughout the years. We re-installed the 1/4" male returns as most from the factory are done kind of "half-as__d". They will need fewer repairs over the years after we did the mods. We also grouped them by 4's in short fans to reduce tangles. The entire cable is in LIKE NEW condition. No dings to the box, or breaks / bends to the jacks or plugs. No internal twisting. The outside cable jacket is cut free. One great thing about this series of cable is that the fan outs are labeled by channel number along their entire length. This snake is ready to use!
Cond. 9.
NEW FROM AMAZON $770.-$940.00
PRE-OWNED
$329.


 

(Click on above thumbnails to enlarge photos)
warranty
PRO-CO
12 / 8 X 4 X 50'
UN-POWERED SNAKE
"STAGE MASTER SERIES"
for sale
Pre-owned and in great condition.
12 channels, 8 XLR sends x 4 TRS, 1/4" sends / returns (means you can use the 1/4" jacks either to send to the board, or return back to stage in any combination. Yes, you can do this with pretty much any snake and any jack / connector [unless it's a 'powered snake' and you're trying to use the speaker portion for signal]. It's simply that this one has a box that is labeled "1-12").
All sends and returns are 2 pair, 24g, 100% foil shielded with gnd.  As it's 100% foil shielded, it is VERY efficient at rejecting RFI (means you won't be picking up any country stations through your PA, due to the snake).
All jacks and plugs are are quality, "Amphenol" brand.
We cut and re-connected the 1/4 plugs at the fan-out, as that is the most fragile part of a snake and commonly where conductors will be strained resulting in broken wires. Again, we cut the wires, de-soldered the internal connection, and re connected / re-crimped the outer sleeve.
No dings to the box, or breaks / bends to the jacks or plugs.
The outside cable jacket is cut free.
This snake is ready to use!
Cond. 8.5
NEW FROM AMAZON $271.00
PRE-OWNED
$139.
 

CLICK HERE FOR NEW STAGE LIGHTING / PAR CANS...

 

(Click on above thumbnails to enlarge photos)

PLATT
Diced-Foam
Utility Case
Model 2005
FOR SALE
Medium-Duty ABS utility case filled with Diced foam and a finger foam lined lid. NEW! Includes keys and catalog. Slight depression to front edge along handle. Does not affect performance. Great for microphones, effect pedals, small mixers, drum-machines, multi-tracks, hard drives etc. Measures inside 20" wide x 14" front-back x ~6" high / deep. Weighs 7 lbs loaded with foam.
Cond. 9.5
SOLD

 

NEW LISTING 11/6/09
(click on above thumbnails to enlarge photos)
warranty
BOGEN
CHALLENGER
PA AMPLIFIER
C-60 C60
60 Watts into loads ranging from 2.6, 8, 10.4, 16 OHM, 12.5 Volt, 25 Volt And 70 volt output PA mixer / amp
 amplifier
for sale
Nice little PA mixer amp from Realistic. Great for Auctioneers, Bingo, Small church's, Schools, retail stores, restaurants, small sporting events or any where portable sound is needed. Will power speaker loads 2.6-16 ohms and will also power paging system based on either 12.5, 25, or 70 volts. 2 mic inputs and a 2 AUX inputs. Also has Master volume and Bass / Treble controls. Unit works great. Our tech completely gone through the unit cleaning and testing all. Large, rear mounted, vertical heat sinks for efficient heat dissipation. Unit produces 60 watts.

-  Attn: This unit utilizes 2501 connectors for the microphone inputs. Unless you have microphone cable that will connect to this, or have adaptors, you would need to modify the microphone input connectors to another format to use them. -

 Measures 14.75" wide x 14" deep x 3.75" tall and weighs 17 lbs unpacked. Includes our standard 30 day limited warranty.
Cond. 8.5
$139.
(Consignment) K.K.


 

AS-IS / CONDITION-UNKNOWN / U-FIX / PARTS 
UNITS BELOW
 

                   NEW LISTING 8/27/07
(click on above thumbnails to enlarge photos)
warranty
YAMAHA
GQ1031
1/3 OCT, 31-BAND EQ
EQUALIZER
MADE IN JAPAN

Same as unit to the left, except operates at a max of 18dbv and does not include XLR I/O's. This is a great, "utility" EQ for mains and especially monitors. Kill feedback and fine tune tone.
Features;
- 1/3 octave / 31 band EQ
- 20Hz-20kHz range
- Overall input level control
- Balanced 1/4" inputs and outputs
- 1 Rack Space in height
- Huge gain and very quiet!
 
Only issue is that the ends of the 530 & 600 Hz lever knobs are sheared off almost flush with the face. Controls still function, but more difficult to grab "on the fly". This unit is in good electronic condition, works and sounds great! No issues. Includes our standard 30 day limited warranty. Looks and works great! 
YAMAHA
Q2031A
Cond. 8
SOLD 1/18/2022
SHIPPING TO RICK IN ARKANSAS

 

  

Furman PL-Plus features:

ü  High performance RFI/EMI noise filter

ü  Triple mode varistor spike and surge protection

ü  RFI / EMI filtering

ü  Circuit breaker, 15-amp rating

ü  Two slide-out, swiveling light fixtures for rack illumination

ü  Eight accessory outlets in rear, controlled by a front panel switch

ü  Dimmer control for lamp brightness

ü  Separate switch for lamps

ü  Line Voltage monitor reads 90 to 128 Volts in 2V steps

ü  Ten-foot, heavy duty 14-gauge AC cord

The Furman PL-PLUS Power Conditioners /  Light Modules is the perfect accessory for any rack-mount system. lnstall in the top slot of your rack, and the eight switched AC outlets on the rear panel will power up all your equipment while its two slide-out light fixtures provide discreet illumination of the controls on stages, in studios, and in other dark places. A dimmer control lets you adjust the lamp brightness to just the right level.
The PL-8 Plus protects your delicate electronic equipment by combining a high-voltage surge and transient suppressor with an RFI/EMI interference filter. The fast-acting suppression circuit responds in less than a nanosecond, clamping transient voltages to safe levels. The peak clamping voltage is 340 VAC, effective for spikes on any of the three AC conductors, and the clamping circuitry can absorb a total of up to 240 Joules. These specifications indicate a very high degree of protection when compared with competitive products. The filter works to prevent noise from fluorescent lights, dimmers, radio transmitters, and similar sources of“electronic pollution” from contaminating the AC line and from there, leaking into sensitive audio, video or computer circuits.
The eight circuit-breaker protected outlets are rated at 15 amps. If the total load on the PL-8 (combining all outlets) exceeds 15 amps, the circuit breaker will trip, cutting off power to your rack.
If this occurs, reduce the load by unplugging one or more units from the PL-8. Then push the black button on the circuit breaker (on the front panel) down and in to reset it.

Model PL-PLUS is an enhanced version of the PL-8. Its front panel provides a handy display of AC line voltage by means of a 20 LED bargraph meter, reading from 90 to 128 Volts in two-volt steps. The normal range voltages are indicated in green, with moderate and extremely high or low voltages in yellow and red respectively. Note that the LED meter continues to read even when the master switch is off. This was done purposely to allow you to check the voltage before powering up. The LEDs are designed for continuous, ongoing use. They consume little power, just a few cents worth per month, much like a clock. The PL-PLUS features 15 amp capacity, as well as a more sophisticated RFI filter network with a greatly improved capacity for stopping line noise. This filter is a low-pass type, composed of high-voltage capacitors and an inductor. It passes the low (50 or 60 Hz) line frequency while rejecting high frequencies, with maximum attenuation in the region from 1 to 100 MHz. The PL-PLUS’ voltmeter has a basic accuracy of +/- 2 volts, (extreme cold or heat may cause an additional one volt of error). Should the voltage reading ever become inaccurate, it can be easily recalibrated by a qualified service technician.

Please note that the voltage reading is advisory only. The PL-PLUS does not compensate for high or low line voltage. If you frequently move your rack to different locations, derive power from generators, use long extension cords, travel internationally or are in an area prone to brownouts, you may benefit from the use of one of Furman’s AR Series AC Line Voltage Regulators.

FURMAN PL-PLUS SPECIFICATIONS

Current rating: 15 Amps (“E” versions 10 Amps)

Input Voltage: 85 to 135 VAC (“E” versions 190 to 270 VAC)

Voltmeter Accuracy: PL-PLUS only: ±2 VAC, calibrated with internal trimpot adjustments

Spike Protection Modes: Line to neutral, neutral to ground, line to ground

Spike Clamping Voltage: Initial turn-on at 200 Volts; TVSS rating of 400 Volts peak at 500 Amps, L-N, N-G, L-G (tested to UL-1449) (Initial turn-on for “E” versions, 390 Volts peak L-N; 680 Volts peak N-G, L-G)

Response time: 1 nanosecond

Maximum surge current: 6,500 Amps

Maximum spike energy: 80 Joules per mode, 240 Joules total protection (“E” versions 130 Joules L-N, 160 Joules N-G, L-G, 450 Joules total)

Noise attenuation: Transverse and common modes: 20 dB at 200 kHz, rising to >40 dB, 1 to 100 MHz

Power Consumption: PL-PLUS, 20 Watts

 Unit looks near new and works great. Comes with a set of 4 rack mount screws. Includes pdf 'e' copy of Furman PL8 / PL-Plus Users / Owners manual. Measures standard rack width, 19" wide x 1U / 1 Rack Space / 1.75" tall x 8" deep and weighs 6 lbs unpacked.
FURMAN PL-PLUS POWER CONDITIONER
SOLD 7/23/17
SHIPPING TO CALIFORNIA
(Consignment) B. McW.

    

     

      NEW LISTING 11/27/07
(click on above thumbnails to enlarge photos)
 warranty
PRE-OWNED
AUDIO CENTRON / SLM
POWER AMPLIFIER
RMA-1000 RMA1000
PROFESSIONAL / STEREO
STABLE INTO 2 OHMS!
MADE IN THE USA!
Circa 1986-94
SOLD 3/29/17
SHIPPING TO IOWA
This is a REAL, 'old skooool' built, CLASS A/B power amp. NOT class d, class g, class t or whatever class marketers are calling them this week, to be the lightest and cheapest amp you can buy, that weighs a couple lbs, but a REAL amp. It's got SIXTEEN output transistors in it!

2 rack space, Audio Centron, RMA-1000 power amplifier. Great for small "All-in-One" speakers, stage monitors, wedge monitors or running horns or mids in a Bi-Amp / Tri-Amp system or for running Low end / subs in mono-mode.
Features:

- Stable down to 2 Ohms!
-
- Power rated as follows;
8 ohms = ~100 wpc
4 ohms = 150 wpc
2 ohms = 220 wpc
- 2-Rack spaces high with built-in rack ears and carry handles
- Cooling fan for those demanding "2 & hard 4 ohm conditions"
- Relay protection against "turn-on / turn-off" transients
- Dual, Front mounted, independent input attenuators
- Dual, LED Signal, Limit and Protect indicators
- Thermal protection with "Fault" LED indicators
- XLR and 1/4" phono input signal I/O's
- Speaker outputs via 3-Way binding / banana posts and 1/4", "all metal" phono jacks
- Stereo / Bridge-Mono selector
- "REAL" TO-3, Metal cased output transistors
- Rear mounted main AC fuse
- Grounded AC input cord

While this unit was originally rated at ~100 wpc @ 8Ω, on our test bench, both this unit's amplifiers produced peak power of 30 volts per channel for 112 watts per channel @ 8 Ω via discrete output & 27.7 volts per channel for 192 watts per channel @ 4 Ω via eight discrete, Motorola, Metal cased, (TO-3) MJI5002 & MJI5001 outputs.

 Again, as stated before, our technician has completely refurb'd this Audio Centron RMA-1000, stereo Power-Amp, cleaning and testing all and it gets our full 'Certification'. Both speaker protection relays just replaced with new. We have completely gone through the unit cleaning and testing all. Unit works great. Only minor issue is that the "Channel B" input attenuator has a blank spot in the first 40% that does not respond to cleaning. Not an issue once you have amp up to operating level.  
SPECS:

- Stable down to 2 Ohms!
- Output Power ratings (stereo mode):
8 ohms = ~100 wpc
4 ohms = 150 wpc
2 ohms = 220 wpc
- Bridge / Mono mode operation ( 440 watts @ 4 ohms)

On our test bench, both amplifiers produce perfectly clean and symmetrical sine waves at both 8 & 4 ohm loads. We tested both internal amplifiers to the above specs, and found them accurate.
This is a great performing, fan cooled amp.
On a personal note; I've actually been using this amp in my studio as a rehearsal amp, but can't really have any 'fan cooled' amps in that environment, so am going to have to go a different route.
Measures 19" wide x 16.5 overall depth / 13.5" rack depth x 3.5" tall and weighs 35 lbs unpacked. Includes our standard 30 day limited  warranty.
AUDIO CENTRON RMA-1000
Condition 8
SOLD 3/29/17
SHIPPING TO IOWA

(Above text, in it's entirety, property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)

 

 

 

(click on above thumbnails to enlarge photos)
warranty
ALESIS
MIDIVERB II 2
EFFECTS UNIT
SOLD OUT OF ALL THE ONE'S I WANT TO SELL RIGHT NOW, BUT MORE WILL LIKELY SHOW UP. HAVE TO KEEP A FEW FOR OUR SYSTEM RACKS.

for sale
Another one well on it's way to becoming a classic. These are great general purpose effects. No you can't program them, but there are plenty of useful factory presets on board. 100 to choose from. 16 bit reverbs, delays, chorus, flange, panning, gated reverbs, reverse gates and reverbs, stereo spatial expansion, and more. Very easy to use. We've used these for years in our racks. Unit works great! Includes copies of owners manual and user pre-set chart. Includes Alesis AC power adapt. Pre-owned. Includes our 30 day limited warranty. 
ALESIS
MIDIVERB II 2
Cond. 8.5
$99.
PS. Killer chorus for guitar!
SOLD OUT OF ALL THE ONE'S WE WANT TO SELL RIGHT NOW, BUT MORE WILL LIKELY SHOW UP. HAVE TO KEEP A FEW FOR OUR SYSTEM RACKS.

 

  (click on above thumbnails to enlarge photos) 
PRE-OWNED
BEHRINGER T1950
8-CHANNEL TUBE MIC PRE-AMP
for sale
SOLD 3/9/15
SHIPPING TO MARYLAND
Rare and no longer available new, the Behringer T1950, 8-Channel tube mic / input pre-amplifier. 8 Fully discrete channels with independent I/O's with both balanced and unbalanced jacks. Very easy to operate. Only issues are cosmetic in that one of the rotary level knobs are missing, there's a chip in one of the plastic meter bezels and two of the 'back lights' are out. Our technician could have replaced it, but the amount of time involved would have, in our opinion, necessitated increasing the price by an impractical amount. He did however change all of the tube back lights.
Features:

- UTC - Ultra Tube Circuitry ‘warms up’ your music without unwanted noise *
- A special "Warmth" control lets you add the amount of tube sound you want
- Selected 12AX7 tubes for outstanding, ultra-musical tube sound
- Gives your music that extra sparkle and definition
- Releases untapped resources and additional details for any program material
- Allows analog signals to maintain all their warmth in digital recordings
- Brings additional warmth and texture to your vocal tracks
- Provides vintage tube sound for guitar and any other instrument
- Adds warmth and presence to any mix
- Perfectly emulates the tape saturation effect of analog tape recording machines
- Servo-balanced gold-plated XLR and¼" TRS inputs and outputs
- Ultra-low noise 4580 audio operational amplifiers for superior sound performance
- High-quality de-tented potentiometers and switches with authentic vintage style knobs
- Huge back-lit analog VU meters with stylish "Retro" design
- High-quality components and exceptionally rugged construction ensure long life
- Conceived and designed by BEHRINGER of Germany

Again, only issues are the cosmetic ones we previously mentioned. Unit is ready to go. Measures standard 19" rack width and 2 spaces tall.
Pre-owned Behringer T1950 8-Channel Mic Pre
SOLD 3/9/15
SHIPPING TO MARYLAND
(Consignment) B.McW.

 

   

 

NEW LISTING 7/5/07
(click on above thumbnails to enlarge photos)
warranty
PRE-OWNED
COMMUNITY
CSX28-S2
12", 2-WAY WEDGE STAGE MONITORS
SOLD 10/24/11
Cab & grill are in great shape. We have completely tested them including sweeping them with an audio generator looking for any acoustical anomalies or extraneous noises or sounds. They work and look great!
below is excerpted from original spec sheet:

"Community is known for building some of the best touring boxes out there. The Community CSX28-S2 is a high output, super-compact, two way stage monitor system. The system utilizes one PZT high frequency driver coupled to an exponential horn and one 12" woofer for high sensitivity and exellent power handling capability. These components are matched to an extremely low-protile enclosure of an optimally tuned, direct radiating, bass reflex design. The recessed handles, black carpert exterior, perforated steel grille, and injection molded corners make this system attractive, rugged and easily transportable."

Specs:
 Freq Response; 70-18,000 Hz
Sensitivity; 97.5 dB 1w/1m
Nominal Dispersion; 90° x 60°
Crossover Freq; 3,000 Hz
Drivers; 12" Woofer / PZT Exponential horn
Driver protection; "PowerSense DDP
Input Connections; Dual Neutrik Speakons & Dual 1/4" Phone jacks
Power Handling; 100 RMS / 250 watts Program / 300 watts max
Finish; Black Ozite Carpet

Tight, deep bass, cutting highs and mids. Great punch and cuts through high stage volumes! These wedges are amazing speakers. Typical, normal cosmetic wear. Made in USA! Each measures 14.5" high x 15.5" wide x 23" deep and weighs 33 lbs unpacked. Includes our standard 30 day limited warranty ( excluding problems due to under / over powering).
Cond. 8
COMMUNITY CSX28-S2
New MSRP $430.00
$159. ea
SOLD 10/24/11
 

    

(click on above thumbnails to enlarge photos)
warranty
INNOVATIVE SOUND SYSTEMS
"DPA-312"
PA / DJ / STEREO SPEAKERS
SOLD 6/21/11
Decent sounding 3-way DJ / Stereo speakers. Horn mids and tweeters. 
Other Features include:

- 12” woofer w/non-deteriorating butyl rubber surround
- 4” poly coated non-deteriorating cloth surrounds
- 4.5” X 10.25” piezo horn with phase plug
- 3” port
- 8 Ω
- 350 watts
- ¼” I/O’S as well as heavy duty 24k binding/banana posts

Covered in black Ozite carpet, these cabinets sport handy inset handles and plastic bumper corners with only normal wear and tear.  We have used these for a couple of DJ gigs and they impressed. All drivers work and sound fine! Tested for all frequencies with a sweep generator. Speakers look and sound GREAT! Each measures 27½" tall x 16" wide x 14.25" deep and weighs 42 lbs unpacked. Includes our standard 30 day limited warranty ( & excluding problems due to under / over powering)
Innovative Sound Systems
"DPA-312"
Cond. 8.5+
$169. pair
SOLD 6/21/11



 

        NEW LISTING 8/26/09
(click on above thumbnails to enlarge photos)
warranty
ALESIS
EFFECTS UNIT
MICROVERB III
#...8438
SOLD 12/14/10
 Good condition and very "useable", Alesis Microverb III. Great for recording / club / church / band systems using 1/4" connections. Made in the USA!

From the Users Manual:

"Born from the original Alesis MICROVERB and MICROVERB II, the units that launched the revolution in low cost professional reverberation, the MICROVERB III carries on this same tradition of world class performance at a phenomenal price. Using 16 bit linear PCM processing like its predecessors, MICROVERB III has 256 programs . . .

The 256 programs in MICROVERB III are the distillation of years of exhaustive research by Alesis into the phenomenon of reverberation. With input from the world’s top recording engineers and producers, the reverb programs were carefully developed on our interactive room simulation and development system. These programs cover every major category of reverb: plates, chambers, halls, and rooms, each with a wide range of sizes and qualities. Included also are a number of special effect programs such as gated and reverse reverbs, as well as a wide variety of ever-useful delay programs . . . "

FEATURES:

- Extremely easy to set up and use
- True 16 bit linear PCM technology
- 85 dB dynamic range
- Full 15kHz bandwidth
- Stereo input and output utilizing ¼” jacks
- Defeat jack on rear for optional foot switch
- +4 dBV capable
- 256 effects programs
- 19" rack mountable

I sold many of these as an Alesis dealer and own a few myself. Great unit to have in your audio "tool box". 256 programs including 144 reverb programs, 95 delay programs & 16 special effects programs. Has high and low frequency equalization, true 16 bit PCM, 85 dB dynamic range, full 15kHz bandwidth, stereo input/output, +4 dBV capability, 256 programs & defeat jack for optional foot switch (great for karaoke or "one man bands". This is a true professional quality unit if you're doing 4-track home recording, using multi-track world class recording equipment or for PA / Sound Reinforcement / Live stage use.

Includes AC power adapt. Pre-owned. Includes our 30 day limited warranty. 
ALESIS
MICROVERB III
Cond. 8.5
$149.
SOLD 12/14/10
  

  

(click on above thumbnails to enlarge photos)

warranty
BOGEN
MTA-30
SOLD 3/25/08

    

(click on above thumbnails to enlarge photos)

warranty
REALISTIC 
MPA-35
4,8,16OHM, 25 And 70 volt output PA mixer / amp
SOLD 3/20/09

(click on above thumbnails to enlarge photos)
warranty
YAMAHA
Q2031A
Dual 31-Band 1/3 Octave EQ
EQUALIZER
MADE IN JAPAN
SOLD 5/11/08

 

 

    

(click on above thumbnails to enlarge photos)
warranty
ALESIS
MICROVERB II 2
EFFECTS UNIT
SOLD 5/11/08

 

 

(click on above thumbnails to enlarge photos)
warranty
SKB
6-U 6U
6 SPACE
RACK CASE
SOLD 3/30/09

 

 

 

(click on above thumbnails to enlarge photos)
warranty
SKB
6-U 6U
6 SPACE
RACK CASE
SOLD 3/30/09

 

 

PHOTOS COMING

NEW LISTING 6/21/07

(Click on above thumbnails to enlarge photos)
warranty
CARVIN
"SNK-16"
16 X 4 X 100'
UN-POWERED SNAKE
SOLD 5/14/08

 

-

-

(Click on above thumbnails to enlarge photos)
LUMITROL
4-CHANNEL
STAGE LIGHTING
CONTROLLER / DIMMER
NEEDS WORK
SOLD 8/15/08


 

(Click on above thumbnails to enlarge photos)

16 GAUGE STEEL
4-SPACE
GEAR RACK 
SOLD

  

(Click on above thumbnails to enlarge photos)

warranty
APOLLO
PORTABLE PA / TAPE DECK
FOR SALE
This British made, self-contained public address system with built-in cassette deck puts out an incredible amount of sound, and that's coming from someone who has sold PA systems for the past 15 years from a few hundred dollars to many tens of thousands of dollars. It would be great for an auctioneer, portable ministry, aerobics, small gathering speaking, bingo, or any other use where a portable, light-weight system that can handle up to about 75 people would be needed. Not only is it loud, but remains VERY clear at higher volumes. The built-in tape decks sound can be mixed with the microphone / keyboard / guitar inputs like a Karoke machine. There are two 1/4" phono (guitar plug) inputs, as well as two RCA inputs (one low and one hi). There is also a 1/4" line input. Outputs include 1/4" phono, RCA, headphone, and an extension speaker output capable of handling a 4 ohm load (which could equal two 8ohm speakers). The output sound is via a heavy-duty 8" speaker. The tape deck features "Soft-Touch" transport controls, a tape counter, cue / review, one-touch-recording, and full auto stop. The carrying handle swings out of the way for use. Besides the grounded AC cord, there is a top mounted receptacle for  a 12-24 DC power input, which means with the right Radio Shack adaptor, it could be used on a cigarette lighter. The unit is built exceptionally well. This is not some cheap Asian import. This was used by a public school system until recently. It is in great shape, and everything works perfectly. We just went through it completely, cleaning and reconditioning the tape deck, and all the switches and controls. The only issue is the speaker grill plastic is wearing out and will need to have it's edges taped or glued. This is only cosmetic and does not affect performance. We are also including a Shure LP300 XLR professional "Live Sound" hand-held microphone with lockable on-off switch and also comes with a cable and bag. If you need a portable PA system to address a small group you will not be disappointed. This will compare to some of the small/mid sized keyboard / acoustic amps available that are much heavier and do not have tape decks built-in. I have sold the Trace Elliots, Crates, Peaveys, and Fenders (which are all great companies) and this is very comparable and lighter!!! Unit measures 15" tall x 13" wide x 8" deep and weighs only 12.5 lbs. PRE-OWNED. INCLUDES OUR 30 day WARRANTY. 
APOLLO
Cond. 9 (due to speaker grill)
SOLD 

(Click on above thumbnails to enlarge photos)
MITCHELL
 STAGE MONITORS
SOLD 10/13/06

 

 

(Click on above thumbnails to enlarge photos)
LT SOUND
THOMPSON ANALOG DELAY
TAD-4
SPRING REVERB / ANALOG DELAY
SOLD 5/30/06


 

  

(Click on above thumbnails to enlarge photos)
warranty
HAFLER
P-225
POWER AMPLIFIER
SOLD

 

     

(Click on above thumbnails to enlarge photos)
warranty
PRE-OWNED
YAMAHA
NS-10M NS10M
NEAR-FIELD STUDIO MONITORS / SPEAKERS
SOLD

 

DOD
R430
2/3 OCTAVE EQUALIZER
SOLD 4/16/04

      
 (Click on above thumbnails to enlarge photos)
warranty
PRE-OWNED
EVENT 
20/20P BI-AMPLIFIED & POWERED STUDIO MONITORS
SOLD 4/24/06

 

   

(Click on above thumbnails to enlarge photos)
warranty
NSI
MC-1600
 DIGITAL
16-CHANNEL
STAGE LIGHTING-CONTROLLER / BOARD
MADE IN THE USA
SOLD 3/28/06

Here are some photos of a few of the configurations we used our MC-1616 with:

     

      

 

 

  



YAMAHA
NS-10M NS10M
STUDIO MONITORS
SOLD 5/19/04

(Click on above thumbnails to enlarge photos)
warranty
CROWN
MX-4 MX4
4-WAY CROSSOVER
#8 (eighth one made!)
SOLD 6/9/04

 

 

(Click on above thumbnails to enlarge photos)
DIGITECH
DSP 256 TO 256XL XL
UPGRADE CHIP PROM
SOLD OUT

TASCAM
M-30
RECORDING MIXER
SOLD

ALESIS
QUADRAVERB PLUS
MULTI-EFFECTS UNIT
SOLD

PEAVEY
XR-600C
"LUNCH-BOX" PA HEAD
MIXER / AMP
SOLD

 

70+ FIXTURE
STAGE LIGHTING SYSTEM
$8500.
SOLD

 

CROWN
D75
POWER AMPLIFIER
SOLD

 

BEHRINGER
CX-2300
CROSSOVER
SOLD

TASCAM
488 MK II
8-TRACK CASSETTE PORTA-STUDIO
SOLD

BEHRINGER
ULTRAPATCH
PX 2000
24 CHANNEL PATCH-BAY
SOLD

SUNN
SR-8200
POWERED PA MIXER
SOLD

 

TEAC
PORTA STUDIO
SOLD

PEAVEY
CS-800
POWER AMPLIFIER
SOLD

BEHRINGER
MDX 4400
"MULTICOM PRO"
4-CHANNEL COMPRESSOR / LIMITER
SOLD

BEHRINGER
XR 4400
"MULTIGATE PRO"
4-CHANNEL NOISE GATE
SOLD

 

AUDIO TECHNICA
STUDIO MIXER / 4 TRACK
MODEL AT-RMX64
SOLD

HOSA
MSB-138
TRIPOD MIC
BOOM STAND
SOLD OUT

 

AURATONE
MONITORS
MODEL 5RC "SUPER-ROAD CUBE"
SOLD

 

AURATONE
MONITORS
MODEL 5RC "SUPER-ROAD CUBE"
SOLD

 
AURATONE 
SUPER-CUBE
SC-5
MONITOR
SOLD

 

RECORDEX
MODEL 345
INDUSTRIAL AUDIO CASSETTE COPY MACHINE.
SOLD

 

NAKAMICHI
MR-1
PRO / STUDIO AUDIO CASSETTE DECK
SOLD

YAMAHA
E-1010
ANALOG DELAY
SOLD

-   

(Click on above thumbnails to enlarge photos)
warranty
DIGITECH
DSP 256
 DIGITAL
MULTI-EFFECTS 
PROCESSOR
These are great single rack space, multi-effect processors for any studio / Live environment. Tons of multi-layered and programmable effects. Full 20-20,00Hz bandwidth. Will do 4 effects at a time! Effects include Reverbs, Chorus, Flange, EQ, Delays, Stereo Panning, Mixers, Gates, Graphic and Parametric EQ's and lots more! Full MIDI capability. This one has all brand new control pots installed, has been factory re-initialized, has been fully tested and is ready to go. Normal battle scuffs and wear, but nothing too serious.
Cond. 7
HELD FROM SALE TILL
FURTHER NOTICE 
 

 

     

TASCAM 
RS-20B
ANALOG DUAL CHANNEL SPRING REVERB
FOR SALE
SOLD

VOCOPRO 
KC-100
KARAOKE
DIGITAL KEY CHANGER
FOR SALE
SOLD

PARAMOUNT
PF-5
POWER AMPLIFIER
SOLD

      NEW LISTING 11/27/07
(click on above thumbnails to enlarge photos)
warranty
PEAVEY
CS-1000X
PROFESSIONAL
POWER AMPLIFIER
MADE IN THE USA!
SOLD 10/31/08
 

 

 

      NEW LISTING 11/27/07
(click on above thumbnails to enlarge photos)
warranty
QSC
MX-1000a
PROFESSIONAL
STEREO POWER AMPLIFIER
MADE IN THE USA!
SOLD 9/26/08
 

BI-AMP
TC-120
POWER AMP
SOLD

 

 

  

 

PEAVEY
M-2600
PROFESSIONAL
POWER AMPLIFIER
SOLD 8/08

(click on above thumbnails to enlarge photos)
warranty
PEAVEY
IP-8.5C
PROFESSIONAL / INSTALLATION
1100 WATT*
POWER AMPLIFIER
SOLD 6/20/07

 

 

 

CREST
VS450
POWER AMPLIFIER
SOLD

 

 

AMERICAN DJ
8-HEAD HELICOPTER DJ LIGHT
SOLD

 

DOD
RTA 4315
31 BAND PINK NOISE GENERATOR / SPECTRUM ANALYZER / RTA
SOLD

 

 

       

(Click on above photos to enlarge)
warranty
TASCAM
MODEL 80-8 
8-TRACK
HALF-INCH
OPEN REEL DECK
SOLD 2/21/04

    

warranty
EV TAPCO 
4400A SPRING REVERB
SOLD 10/15/03

warranty
BOSE
800E 802 800-E 
SYSTEM EQUALIZER / CONTROLLER
SOLD

 

    

FOSTEX 
3180
DUAL CHANNEL SPRING REVERB
SOLD

 

    

DAWN
S-510
SATELLITE PA SPEAKER
SOLD

 

 

    

BOSE
802 SERIES II
PA SPEAKER / SOUND SYSTEM SPEAKER
SOLD 1/12/04
 

 

warranty
BOSE
WSC-1
WAVE SYSTEM CONTROLLER
SOLD 1/12/04

TASCAM
M-2600
MIXING CONSOLE / MIX BOARD
SOLD